These buttons are used to scroll through the menu. Use these +/- buttons when using the handlebar controller's menu via the orange RESET button (see above). They can then control some of the ride such as pausing/starting and adjusting the workout's difficulty using the RESET button's menu. When more than one rider is present, pressing both +/- keys at the same time allows that rider to become the leader.
![computrainer manual computrainer manual](https://media.dcrainmaker.com/images/2009/02/in-depth-computrainer-review-3.jpg)
So if that hill isn't hard enough make it harder! These buttons adjust the riders gradient percentage. Any changes to your FTP are not permanently saved, it only changes during the workout.
![computrainer manual computrainer manual](https://i.pinimg.com/originals/88/2c/42/882c42300fa942869a828caa2fd2f620.gif)
These blue buttons adjust the rider's current FTP value when a workout is loaded. When a trainer has never been calibrated you'll see a N/C for "Not Calibrated" in the RRC area. This makes it easy for the leader/administrator to see if riders are properly calibrating their trainers. Your current RRC is always displayed up on your rider display and briefly blinks when it changes. This can be done at any time during a ride. Pressingį3 again sets the new calibration value and continues the ride. Once F3 is pressed, the rider can do the typical spin up past 25mph, coast down and let the CT calculate your new rolling resistance calibration number or RRC. See more about: cycling, bike, bikes, endurance sports, gear, beginning cyclist, cycling. Visit Joe Friel 's Coach Profile Joe Friel’s Quick Guide to Setting Zones TrainingPeaks Joe Friel, Power-Time-Weight Comparisons, Computrainer Workout Manual, Racermate Inc.
#Computrainer manual manual
This button puts the rider into calibration mode during a ride. Friel Manual Racermate plans on TrainingPeaks. The various screens include the default stats/averages screen, the power screen, zones screen, and course/climbing screen. Within the power display, FTP and LTHR are displayed when using theīuilt-in FTP Test. This button toggles through each rider’s display screens to show the various statistical data for their ride. Rider display showing the Handlebar Controller popup menu. The leader can press F1 again to continue the ride. Mode, which is just like pressing F3 (refer to F3 info). When there is more than one rider, the leader of the session can pause everyone's ride by using the F1 key whereas anyone else pressing F1 goes into calibration This makes it easy to manually do multiple laps while training. Some options include toggling the workout timer, finishing their ride early, and finding their ANT+ devices.įor single-rider use, F1 controls the lap counter. Using the RESET button, riders can open their controller menu then use the +/- keys to scroll through the various menu options. This is the big orange button that displays the controller menu for each individual rider. When using PerfPRO Studio, here's what the various buttons on the handlebar controller command: Ive never experienced any major problems with the ear HR monitor on the CompuTrainer.
![computrainer manual computrainer manual](https://ep1.pinkbike.org/p4pb16870308/p4pb16870308.jpg)
#Computrainer manual software
However - I agree that some of the software isnt easy to use at first, but once you figure it out - its hard to live without. More information on ANT+ Enabled handlebar controllers. Computrainer is absolutely awesome for getting fit when you are off the roads like we are here in the northeast for the winter.
![computrainer manual computrainer manual](https://media.dcrainmaker.com/images/2017/02/the-new-computrainer-training-room-13.jpg)
With PerfPRO Studio the rider has total control of their ride using the CT handlebar controller. Good luck, let us know if you get it to work.Handlebar Controller Options for CompuTrainer Users Hope that helps? I have not tried Rouvy but I have had it work with Sufferfest, trainer road, and Xert player all connecting as ant+ FEC. If that does not work make certain that the CT bridge is the first thing you fire up always and make sure that garmin is not running in the background and interfering with your ant stick. Connect to that and you should have everything, do not connect anything else since you get cadence, speed and power all from the computrainer. Once this is confirmed the next thing is to go to the program and search for the ant+ FEC trainer., it will have the ant ID as seem on the perfpro CT screen upper right hand corner. The sequence is normally, first get the perfpro ct bridge running and connected to your trainer, confirm it is working by spinning and looking at the perfpro display. I would say not to connect any other power meters this will screw things up. The first thing to did you click on add trainer? If it is linked up and working you will see the power and speed change in step with the effort you are doing on the bike.